Automatic Control Equipment (FSI-VPR)

Academic year 2026/2027
Supervisor: doc. Ing. Pavel Škrabánek, Ph.D.  
Supervising institute: ÚAI all courses guaranted by this institute
Teaching language: Czech
Course type: departmental course
Aims of the course unit:

The aim of the course is to introduce students to electrical, pneumatic, and digital technical tools used for the control of technological processes, as well as to tools for human–machine interaction, data storage, information transfer, and information processing. After completing the course, students will be able to use, configure, and appropriately integrate these tools into control and regulation systems.

Learning outcomes and competences:
 
Prerequisites:

Prerequisites include basic knowledge of automatic control, programming, mathematics, and physics, all at the level covered in previously completed university courses.

Course contents:

The course provides a basic overview of instrumentation and software tools used in the automatic control of technological processes. Throughout the course, students will become familiar with electrical, pneumatic, and software tools used in automation, as well as with the transmission of information between these tools, control systems, and visualization and operator interface devices.

Teaching methods and criteria:
 
Assesment methods and criteria linked to learning outcomes:

Knowledge and skills are assessed through credit and examination.

Requirements for credit: Attendance at exercises, completion of assigned laboratory tasks, and preparation of a written report based on measurements. Attendance at exercises is mandatory; if this condition is not met, each case is assessed individually by the course instructor. Laboratory exercises are evaluated by the instructor based on student activity, and the laboratory report must be submitted and approved.

Requirements for the examination: Completion of a written test covering knowledge gained in lectures and exercises, followed by an oral examination. Answers to questions are graded with points, and the examination is evaluated according to the A-F scale.

Participation in lectures is recommended, while attendance at exercises is monitored. The method of compensating for missed classes is at the discretion of the exercise supervisor.

Controlled participation in lessons:
 
Type of course unit:
    Lecture  13 × 2 hrs. optionally                  
    Laboratory exercise  13 × 2 hrs. compulsory                  
Course curriculum:
    Lecture

  1. Introduction to automation components. Hierarchy of control levels in industrial automation. Signals for transmission and processing of information. Pulse modulation.

  2. Active sensors (thermoelectric, piezoelectric, pyroelectric, inductive) and passive sensors (inductance-based, Hall-effect, capacitive, resistive).

  3. Electrical signal conditioning using passive and active circuits.

  4. Analog controllers based on operational amplifiers. Digital controllers.

  5. Control elements and actuators. Types of electric motors and servomotors.

  6. Transmission paths and their connectivity. Transmission of analog signals over metallic lines. Digital signal transmission and standards for serial communication over metallic conductors.

  7. Serial communication interfaces for connecting sensors and actuators. Industrial communication buses.

  8. Human–machine interfaces (HMI).

  9. Principles and properties of compressed air. Pneumatic circuit diagrams. Components for the generation and distribution of compressed air.

  10. Pneumatic actuators and control. Types of pneumatic cylinders, motors, and valves.

  11. Electropneumatic components and circuits.

  12. Practical applications of pneumatic technologies.

  13. Review.

    Laboratory exercise

  1. Working with electronic measuring instruments (multimeters, generators, oscilloscopes).

  2. System identification.

  3. Passive and active filters.

  4. Various operational amplifier configurations (voltage follower, voltage amplifiers, PID controller).

  5. Control of electric motor speed using pulse-width modulation.

  6. A/D and D/A converters.

  7. Serial signal transmission (e.g., RS-232 and RS-485).

  8. Design of a printed circuit board for a given task.

  9. Basics of pneumatic components, properties, and calculations.

  10. Pneumatic mechanisms and their control.

  11. Practical design and simulation of pneumatic circuits.

  12. Practical design and simulation of pneumatic circuits.

  13. Course credit (assessment).

Literature - fundamental:
1. Němec, Z.: Prostředky automatického řízení, elektrické. Studijní opora oboru Aplikovaná informatika a řízení. VUT Brno, FSI, ÚAI.2016 Dostupné z http://www.fme.vutbr.cz/elearning...
2. Thomas, C.: Sensor Fusion - Foundation and Applications, InTech, 2011
3. Isermann, Rolf: Mechatronic systems—fundamentals, Springer Netherlands, 2008
4. Haluza, J.: Prostředky automatického řízení, tekutinové. Studijní opora oboru Aplikovaná informatika a řízení. VUT Brno, FSI, 2002.
5. Haluza, J.: Prostředky automatického řízení, tekutinové. Studijní opora oboru Aplikovaná informatika a řízení. 1. vyd. VUT Brno, FSI, 2002.
6. Debeljkovic, D: Time-Delay Systems, InTech, 2011
7. Mitchell, H.B: Multi-Sensor Data Fusion - An Introduction, Springer - Verlag, 2007
8. LabVIEW Measurements Manual, National Instruments, April 2003 Edition, Part Number 322661B-01, dostupné z www.ni.com
9. Rey, G.R., Muneta L. M: Modelling Simulation and Optimization, InTech, 2010
10. Fraden, Jacob: Handbook of Modern Sensors - Physics, Designs and Applications (3rd Edition), Springer - Verlag, 2004
11. Isermann, Rolf: Mechatronic systems—fundamentals, Springer Netherlands, 2008
12. Balátě, J.: Technické prostředky automatického řízení. Praha, SNTL 1986.
13. Beneš, P. a kol.:Automatizace a automatizační technika, díl 3- Prostředky automatizační techniky. Computer Press, Praha, 2000.
Literature - recommended:
1. Balátě, J. : Technické prostředky automatického řízení. Praha, SNTL 1986.
2. Beneš, P. a kol.:Automatizace a automatizační technika, díl 3- Prostředky automatizační techniky. Computer Press, Praha, 2000.
3. Švarc, a kol.: Automatické řízení, CERM, Brno, 2011.
4. Kopáček, J.: Pneumatické mechanismy.
5. FESTO Didactic: Pneumatické řídicí systémy.
6. FESTO Didactic: Úvod do řízení programovatelným automatem
7. Škopán, M.: Hydraulické pohony strojů. Studijní text - sylabus, VUT Brno, 2004.
8. Firemní literatura, katalogy a webovské stránky automatizačních firem.
9. Nilsson, J. W.: Electric Circuits. Addison-Wesley Publishing Company, 1990.
The study programmes with the given course:
Programme Study form Branch Spec. Final classification   Course-unit credits     Obligation     Level     Year     Semester  
B-STR-P full-time study AIŘ Applied Computer Science and Control -- Cr,Ex 5 Compulsory 1 2 S
C-AKR-P full-time study CLS -- Cr,Ex 5 Elective 1 1 S