Ing. Miloslav Kouřil, CSc.
E-mail:   kouril@fme.vutbr.cz 
Dept.:   Institute of Materials Science and Engineering
Dept. of Metal Materials
Position:   Assistant Professor
Room:   A3-old/305

Education and academic qualification

  • 1982;Ing.;Faculty of mechanical engineering TU Brno;branche mechanical technology
  • 1996;CSc.;Faculty of mechanical engineering TU Brno; Brance Physical metalurgu and the limit states of materials

Career overview

  • 1983-1986 a postgraduate student at FS VUT Brno,the chair of material science
  • 1986-1989 a research worker at FS VUT Brno, the chair of material science
  • 1989-now an asistant professor at FSI VUT, Institut of the material engineering, the branche of material science

Scientific activities

  • The phase transformations, metalography, the heat and chemical heat treatment of metals

Sum of citations (without self-citations) indexed within ISI Web of Knowledge

1

Sum of other citations (without self-citations)

2

Supervised courses:

Publications:

  • MIKMEKOVÁ, Š.; MAN, O.; PANTĚLEJEV, L.; HOVORKA, M.; MÜLLEROVÁ, I.; FRANK, L.; KOUŘIL, M.:
    Strain mapping by Scanning Low Energy Electron Microscopy,
    Key Engineering Materials (print), Vol.465, (2011), No.1, pp.338-341, ISSN 1013-9826, Trans Tech Publications
    journal article - other
  • ŠENBERGER, J., BUCHAL, A., FILÍPEK, J., BŘEZINA, R., KOUŘIL, M.:
    Použití isotermicky zušlechtěné litiny s kuličkovým grafitem pro výrobu odlitků se zvýšenou odolností proti abrazi zejména na náhradní díly zemědělských strojů,
    Slévárenství, Vol.LII, (2004), No.11-12, pp.456-460, ISSN 0037-6825, Svaz sléváren ČR
    journal article - other
  • Dlouhý Ivo, Stolař Pavel, Kouřil Miloslav:
    Rapid Austenitizing As a Method of Martensitic Steel Toughening

List of publications at Portal BUT

Abstracts of most important papers:

  • MIKMEKOVÁ, Š.; MAN, O.; PANTĚLEJEV, L.; HOVORKA, M.; MÜLLEROVÁ, I.; FRANK, L.; KOUŘIL, M.:
    Strain mapping by Scanning Low Energy Electron Microscopy,
    Key Engineering Materials (print), Vol.465, (2011), No.1, pp.338-341, ISSN 1013-9826, Trans Tech Publications
    journal article - other
    The use of the scanning low energy electron microscopy (SLEEM) has been slowly making its way into the field of materials science, hampered not by limitations in the technique but rather by relative scarcity of these instruments in research institutes and laboratories. This paper reports the results obtained from an investigation of the microstructure of ultra fine-grained (UFG) copper fabricated using equal channel angular pressing (ECAP) method, namely in the as-pressed state and after annealing. SLEEM is very sensitive to the perfection of crystal lattice and using SLEEM, local strain can be effectively imaged.
  • ŠENBERGER, J., BUCHAL, A., FILÍPEK, J., BŘEZINA, R., KOUŘIL, M.:
    Použití isotermicky zušlechtěné litiny s kuličkovým grafitem pro výrobu odlitků se zvýšenou odolností proti abrazi zejména na náhradní díly zemědělských strojů,
    Slévárenství, Vol.LII, (2004), No.11-12, pp.456-460, ISSN 0037-6825, Svaz sléváren ČR
    journal article - other
    Spheroidal graphite cast iron (ADI) isotermally treated at temperatures 200 up 300 C during 10 up 240 min, investigation of structure by X ray diffraction, influence of temperature and isothermal holding time hardness and austenite content in structure, measured parameters of alpha and gamma lattice for used states of thermal treatment, manufacture of tools for a agricultural machines. Examining of plough tools from ADI cast iron during field trials.
  • Dlouhý Ivo, Stolař Pavel, Kouřil Miloslav:
    Rapid Austenitizing As a Method of Martensitic Steel Toughening